| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Fix a ublk recovery hang, where END_USER_RECOVERY without a
successful START_USER_RECOVERY could be satisfied by a stale
completion latch
- Fix a stack out-of-bounds read in the CDROMVOLCTRL ioctl
- MAINTAINERS email address update for Roger Pau Monne
* tag 'block-7.2-20260724' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
MAINTAINERS: update my email address
cdrom: fix stack out-of-bounds read in CDROMVOLCTRL
ublk: wait on ublk_dev_ready() instead of ub->completion
|
|
Pull drm fixes from Dave Airlie:
"Weekly drm pull request, small and scattered seems to be the new
normal, the ttm change is probably the largest, with xe being the
most. Alex was out this week so amdgpu is smaller and only has some
urgent fixes.
MAINTAINERS:
- update mailmap address
ttm:
- backup pages using correct order
gpusvm:
- fix mm leak on eviction
- properly zero page array in mm scanning
tests:
- fix dma mask errors in tests
panel:
- fix dependency issues
- ilitek-ili9881c - fix probing
i915:
- Remove DP_EDP_BACKLIGHT_AUX_ENABLE_CAP check for DPCD backlight
xe:
- Skip invalidation for purgeable state updates
- Add drm_dev guards when detaching CCS read / write buffers
- Alloc per domain unique i2c id
- Fix SVM leak on resv obj alloc failure in xe_vm_create
amdgpu:
- Fix a backport mistake for dm_gpureset_toggle_interrupts()
- Fix a failure on flip-done timeouts for mode1 reset
appletbdrm:
- fix issue in damage handling
amdxdna:
- fix command timeout race
imagination:
- fix gpu vm locking
vc4:
- prevent trusted bo from being mapped again
- prevent timer rearm on shutdown
v3d:
- fix NULL deref in unbind
- idle AXI before clock disable on suspend
- use proper GMP access for newer hw
vmwgfx:
- validate shader array size
ethosu:
- fix length calculations
- handle internal chaining buffers
gma500:
- return errors from HDMI i2c reads"
* tag 'drm-fixes-2026-07-25' of https://gitlab.freedesktop.org/drm/kernel: (31 commits)
drm/amd/display: Fix missing DCE check in dm_gpureset_toggle_interrupts()
drm/amd/display: Fix flip-done timeouts on mode1 reset
Revert "drm/pagemap: Guard HPAGE_PMD_ORDER use with CONFIG_ARCH_ENABLE_THP_MIGRATION"
drm/vc4: Shut down BO cache timer before teardown
drm/tests: shmem: Set DMA mask to 64-bit in drm_gem_shmem
drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create()
drm/xe/i2c: Allow per domain unique id
drm/gma500: return errors from Oaktrail HDMI I2C reads
drm/vc4: hvs/v3d: Fix null dereference in unbind
drm/panel: fix unmet dependency bug for DRM_PANEL_HIMAX_HX83121A
drm/panel: s6e3ha8: fix unmet dependency on DRM_DISPLAY_HELPER
drm/panel: ilitek-ili9882t: fix unmet dependency for DRM_PANEL_ILITEK_ILI9882T
drm/panel: ilitek-ili9881c: do not fail probe if iovcc is absent
drm/v3d: Idle AXI transactions before disabling the clock on suspend
drm/v3d: Reach the GMP through the hub registers on V3D 7.x
mailmap: Update Maíra Canal's email address
drm/pagemap: Guard HPAGE_PMD_ORDER use with CONFIG_ARCH_ENABLE_THP_MIGRATION
drm/pagemap: Clear driver-provided PFNs from migration PFN array
drm/xe/vf: Add drm_dev guards when detaching CCS read/write buffers
accel: ethosu: Handle U85 internal chaining buffer
...
|
|
Pull ceph fixes from Ilya Dryomov:
"A bunch of assorted fixes with the majority being hardening against
malformed input and invalid data scenarios that don't happen in real
deployments but can be utilized to trigger use-after-free and similar
issues, some error path leak fixups and two patches from Max to avoid
a potential hang in __ceph_get_caps() and unintended nesting of
current->journal_info while handling replies from the MDS.
All marked for stable"
* tag 'ceph-for-7.2-rc5' of https://github.com/ceph/ceph-client:
ceph: avoid fs reclaim while using current->journal_info
ceph: add owner/capability checks for CEPH_IOC_SET_LAYOUT*
ceph: fix hanging __ceph_get_caps() with stale mds_wanted
rbd: Reset positive result codes to zero in object map update path
libceph: bound pg_{temp,upmap,upmap_items} length to CEPH_PG_MAX_SIZE
libceph: refresh auth->authorizer_buf{,_len} after authorizer update
ceph: fix refcount leak in ceph_readdir()
libceph: guard missing CRUSH type name lookup
libceph: remove debugfs files before client teardown
libceph: bound get_version reply decode to front len
ceph: fix writeback_count leak in write_folio_nounlock()
libceph: fix two unsafe bare decodes in decode_lockers()
ceph: fix pre-auth out-of-bounds read on snaptrace in ceph_handle_caps()
libceph: Reject monmaps advertising zero monitors
libceph: reject zero bucket types in crush_decode
libceph: Fix multiplication overflow in decode_new_up_state_weight()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's a bit all over the place, as I was hoping to fix a decade-old bug
in our seccomp handling on syscall entry and ended up collecting other
fixes in the meantime. You'll see the failed attempt (+revert) here
but I didn't want to hold off on the others any longer. Hopefully
we'll get that one squashed next week...
- Fix early_ioremap() of unaligned ACPI tables
- Remove bogus information from data abort diagnostics
- Fix kprobes recursion during single-step
- Fix incorrect constant in ESR address size fault macro
- Fix OOB page-table walk in memory hot-unplug notifier
- Fix OOB access to the linear map when retrieving an unaligned huge pte
- Fix MPAM register reset values
- Fix MPAM NULL dereference on teardown"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: make huge_ptep_get handled unaligned addresses
arm64/mm: Check the requested PFN range during memory removal
arm64: Correct value returned by ESR_ELx_FSC_ADDRSZ_nL()
arm64: kprobes: Allow reentering kprobes while single-stepping
arm64: kprobes: Only handle faults originating from XOL slot
drivers/virt: pkvm: Fix end calculation in mmio_guard_ioremap_hook()
Revert "arm64: syscall: Ensure saved x0 is kept in-sync with tracer updates"
arm64: mm: When logging data aborts only decode Xs when ISV=1
arm64: fixmap: Allow 256K early_ioremap() at any offset
arm_mpam: guard MBWU state before adding it to garbage
arm_mpam: Fix MPAMCFG_MBW_PBM register setting
arm_mpam: Fix software reset values of MPAMCFG_PRI
arm64: syscall: Ensure saved x0 is kept in-sync with tracer updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Will Deacon:
"Joerg's away at the moment so I've been looking after the IOMMU tree
in his absence. In the process of doing that, I've hoovered up a
handful of fixes for the AMD and Intel drivers which address a
combination of the usual out-of-bounds/locking/leak bugs as well as
some logical issues around SVA and command completion.
AMD:
- Fix lockdep splat from nested domain allocation
- Fix nested domain leak
- Fix broken synchronisation of command completion
- Fix OOB write in "ivrs_acpihid" command-line parsing
VT-d:
- Prevent SVA for IOMMUs with non-coherent page-table walker
- Fix OOB write in PMU driver"
* tag 'iommu-fixes-v7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommu/intel: Fix out-of-bounds memset in dmar_latency_disable()
iommu/amd: Bound the early ACPI HID map
iommu/vt-d: Disallow SVA if page walk is not coherent
iommu/amd: Wait for completion instead of returning early in iommu_completion_wait()
iommu/amd: Fix nested domain leak
iommu/amd: Fix IRQ unsafe locking in gdom allocation
|
|
This line was lost when cping from amd-staging-drm-next to drm-fixes.
So add it back.
Cc: stable@vger.kernel.org
Fixes: 8382cd234981 ("drm/amd/display: consolidate DCN vblank/flip handling onto vupdate_no_lock")
Reported-by: Lu Yao <yaolu@kylinos.cn>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260723134450.13838-1-sunpeng.li@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
The vblank on/off callbacks mixed use of amdgpu_irq_get/put() and
amdgpu_dm_crtc_set_vupdate_irq() to enable and disable IRQs.
With get/put, base driver will callback into DC to disable IRQs when
refcount == 0. With set_vupdate_irq(), DC is called directly to disable
IRQs, bypassing base driver's refcount tracking.
During gpu reset, base driver can restore IRQs via
amdgpu_irq_gpu_reset_resume_helper() > amdgpu_irq_update(). So if
get/put() is not used (i.e. refcount == 0), then vupdate_irq will be
disabled.
This is problematic if DRM requests vblank on before amdgpu_irq_update()
is called: drm_vblank_on() > set_vupdate_irq() enables vupdate_irq, but
the refcount is still 0. gpu_reset_resume_helper() > irq_update() then
immediately disables it, thus leading to flip done timeouts.
This is made worse on DCN since VUPDATE_NO_LOCK is the only IRQ enabled.
Prior to 8382cd234981, a combination of GRPH_FLIP and VSTARTUP IRQs were
used, and they used get/put(). This explains why 8382cd234981 exposed
this issue.
Fix by using get/put() instead of set_vupdate_irq(). DCE is unchanged,
since it relies on unbalanced enable/disable calls based on VRR status,
and hence requires direct set_vupdate_irq(). Plus, it also uses
GRPH_FLIP and VLINE IRQs, which are properly tracked by get/put().
Cc: stable@vger.kernel.org
Fixes: 8382cd234981 ("drm/amd/display: consolidate DCN vblank/flip handling onto vupdate_no_lock")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260723180159.52121-1-sunpeng.li@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v7.2-rc5:
- Improve damage handling in appletbdrm.
- Fix harmful fragmenting of MM by backing up TTM pages at native
page order.
- Fix timeout handling in amdxdna.
- Fix imagination locking for map/unmap operations.
- Fix mm leak in gpusvm eviction.
- Properly zero page array in gpusvm mm scanning.
- Prevent trusted shader bo's from being mapped again in vc4.
- Validate shader array size in vmwgfx.
- Fix length calculation bugs in ethosu.
- Better error handling during pagemap migration.
- Improve v3d suspend.
- Kconfig updates for some panels.
- Handle missing iovcc in ili9881c panel.
- Fix vc4 unbind.
- Add i2c error handling in gma500.
- Fix kunit tests on pp64le and s390x.
- Prevent rearming vc4 timer on shutdown.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patch.msgid.link/07284633-6b9b-40f9-8949-b1516a42a34c@linux.intel.com
|
|
CONFIG_ARCH_ENABLE_THP_MIGRATION"
This reverts commit 04b177544a040cbafab760d6b766381c6b22e0a8.
The original author requested it to be reverted, as it conflicts with
changes in the -next branch for MM:
"I'm not sure who is doing the drm-misc-fixes PR, but if you are can
you omit this patch: https://patchwork.freedesktop.org/series/170865/
I guess this conflicts with MM changes in their next tree and it easy
enough on our side to do this slightly differently to avoid a conflict
so going to post revert + a different change. If this is already sent nbd."
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
The BO cache timer callback schedules time_work, and time_work can rearm
the timer through vc4_bo_cache_free_old().
vc4_bo_cache_destroy() deletes the timer and then cancels the work, which
does not break that cycle: the work being cancelled can rearm the timer,
and the timer then queues work again after teardown.
Use timer_shutdown_sync() instead, so the timer cannot be rearmed and the
cycle ends with cancel_work_sync().
Fixes: c826a6e10644 ("drm/vc4: Add a BO cache.")
Cc: stable@vger.kernel.org
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Link: https://patch.msgid.link/20260720084426.1632508-1-lilinmao@kylinos.cn
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Skip invalidation for purgeable state updates (Arvind)
- Add drm_dev guards when detaching CCS read / write buffers (Satyanarayana)
- Alloc per domain unique i2c id (Raag)
- Fix SVM leak on resv obj alloc failure in xe_vm_create (Shuicheng)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patch.msgid.link/amJ5-WUA_OS_RBAp@fedora
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Lots of fixes, double the count even for the 'new normal'. Largely due
to my time off followed by a networking conference which distracted
most maintainers (less so the AI generators).
Including fixes from Bluetooth and WiFi.
Current release - regressions:
- wifi: mt76: fix MAC address for non OF pcie cards
Current release - new code bugs:
- mptcp: fix BUILD_BUG_ON on legacy ARM config
- wifi: cfg80211: guard optional PMSR nominal time
Previous releases - regressions:
- qrtr: ns: raise node count limit to 512, we arbitrarily picked
256 as a limit, turns out it was too low for real world deployments
- vhost-net: fix TX stall when vhost owns virtio-net header
- eth: amd-xgbe: fix MAC_AUTO_SW handling in CL37 AN
- wifi: ath12k: fix low MLO RX throughput on WCN7850
Previous releases - always broken:
- number of random AI fixes for SCTP, RDS and TIPC protocols
- more AI-looking fixes for WiFi drivers
- number of fixes for missing pointer reloading after skb pull
- reject BPF redirect use from qdisc qevent block
- tcp: initialize standalone TCP-AO response padding
- vsock/virtio: collapse receive queue under memory pressure to avoid
client OOMing the host with tiny messages
- ipv4: icmp: fill flow parameters in icmp_route_lookup decoy lookup,
make sure the ICMP response routing follows the routing policy
- gro: fix double aggregation of flush-marked skbs
- ovpn: fix various refcount bugs
- tls: device: push pending open record on splice EOF
- eth: mlx5:
- use sender devcom for MPV master-up
- fix MCIA register buffer overflow on 32 dword reads"
* tag 'net-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (234 commits)
drop_monitor: perform u64_stats updates under IRQ-disabled section
drop_monitor: fix size calculations for 64-bit attributes
net: drop_monitor: fix info leak in NET_DM_ATTR_PAYLOAD
mptcp: fix BUILD_BUG_ON on legacy ARM config
selftests: mptcp: userspace_pm: fix undefined variable port
mptcp: fix stale skb->sk reference on subflow close
mptcp: pm: userspace: fix use-after-free in get_local_id
mptcp: decrement subflows counter on failed passive join
mac802154: hold an interface reference across the scan worker
sctp: don't free the ASCONF's own transport in DEL-IP processing
phonet: check register_netdevice_notifier() error in phonet_device_init()
phonet: pep: fix use-after-free in pep_get_sb()
bnge/bng_re: fix ring ID widths
tipc: fix integer overflow in tipc_recvmsg() and tipc_recvstream()
net: airoha: fix ETS channel derivation in airoha_tc_setup_qdisc_ets()
mctp: check register_netdevice_notifier() error in mctp_device_init()
ptp: netc: explicitly clear TMR_OFF during initialization
rds: tcp: unregister sysctl before tearing down listen socket
ipv6: Change allocation flags to match rcu_read_lock section requirements
net: slip: serialize receive against buffer reallocation
...
|
|
In a reply message to an RBD request, a positive result code indicates
a data payload, which is not allowed for writes. While
rbd_osd_req_callback() already resets a positive result code for writes
to zero, rbd_object_map_callback() does not. This allows a corrupted
reply to an object map update to trigger the rbd_assert(*result < 0) in
__rbd_obj_handle_request(). This happens, because
rbd_object_map_callback() calls rbd_obj_handle_request() ->
__rbd_obj_handle_request() and passes this positive result code. From
__rbd_obj_handle_request(), rbd_obj_advance_write() is called, which
leaves the positive result code unchanged and returns true. Therefore,
the if(done && *result) branch is executed in __rbd_obj_handle_request()
and the assertion triggers.
This patch fixes the issue by adjusting the logic in the
rbd_object_map_callback() path. A positive result code for an object map
update is now reset to zero (similar to rbd_osd_req_callback()), and the
message is subsequently handled the same way as if the result code was
zero from the beginning. Additionally, a WARN_ON_ONCE() is added for
this case.
Cc: stable@vger.kernel.org
Fixes: 22e8bd51bb04 ("rbd: support for object-map and fast-diff")
Signed-off-by: Raphael Zimmer <raphael.zimmer@tu-ilmenau.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Firmware requires more than 16 bits to address TX ring IDs for its
internal QP management. Widen the associated HSI ring ID fields to
32 bits. The values firmware assigns remain within 24 bits, bounded
by the hardware doorbell XID field.
The fw_ring_id field belongs to bnge_ring_struct, a common struct
shared by all ring types, so widening it to u32 applies uniformly
across TX, RX, CP, and NQ rings but firmware assigns values within
16-bit range for all ring types except TX, which requires the wider
field.
Note that, Thor Ultra hardware has not yet been deployed and no
firmware has been released to field, so backward compatibility
is not a concern.
Fixes: 42d1c54d6248 ("bnge/bng_re: Add a new HSI")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Dharmender Garg <dharmender.garg@broadcom.com>
Reviewed-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Link: https://patch.msgid.link/20260721063731.2622500-1-vikas.gupta@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Antonio Quartulli says:
====================
Included fixes:
* ensure keepalive timestamps are computed using monotonic source
* avoid UAF in unlock_ovpn() when iterating over release_list
* fix memleak in selftest tool
* ensure reference to peer is acquired before scheduling worker
(which may drop the not-yet-taken ref)
* fix refcount leak in case of concurrent TX and RX TCP error
* fix potential refcount unbalance in case of sock release in
P2P mode
* tag 'ovpn-net-20260720' of https://github.com/OpenVPN/ovpn-net-next:
ovpn: use monotonic clock for peer keepalive timeouts
ovpn: fix use after free in unlock_ovpn()
selftests/net: ovpn: fix getaddrinfo memory leak in ovpn_parse_remote()
ovpn: hold peer before scheduling keepalive work
ovpn: fix peer refcount leak in TCP error paths
ovpn: avoid putting unrelated P2P peer on socket release
====================
Link: https://patch.msgid.link/20260720144131.3657121-1-antonio@openvpn.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Derive the hardware QoS channel from opt->parent instead of opt->handle
in airoha_tc_setup_qdisc_ets(). The ETS qdisc handle is either
user-specified or auto-allocated by qdisc_alloc_handle() and bears no
relation to the HTB leaf classid that identifies the hardware channel.
HTB derives the channel from TC_H_MIN(opt->classid), and ETS is always
attached as a child of an HTB leaf, so its opt->parent matches that
classid. Using opt->handle instead can cause two ETS qdiscs on different
HTB leaves to collide on the same hardware channel, corrupting scheduler
configuration and stats.
Fixes: 20bf7d07c956 ("net: airoha: Add sched ETS offload support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260720-airoha-ets-handle-fix-v2-1-6f7129ddc06f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The NETC timer does not support function level reset, so TMR_OFF_L/H
registers are not cleared by pcie_flr(). If TMR_OFF was set to a
non-zero value in a previous binding, it will persist across driver
rebind and cause inaccurate PTP time.
There is also a hardware issue: after a warm reset or soft reset,
TMR_OFF_L/H registers appear to be cleared to zero, but the timer clock
domain internally retains the stale value. When the timer is re-enabled,
TMR_CUR_TIME continues to track the old offset until TMR_OFF is written
explicitly. This can cause incorrect PTP timestamps and even PTP clock
synchronization failures.
Per the recommendation from the IP team, explicitly write 0 to TMR_OFF
in netc_timer_init() to flush the internally cached value and ensure
TMR_CUR_TIME follows the freshly initialized counter.
Fixes: 87a201d59963 ("ptp: netc: add NETC V4 Timer PTP driver support")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260720012508.23227-1-wei.fang@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sl_realloc_bufs() replaces rbuff and updates buffsize while holding
sl->lock. slip_receive_buf() reads those fields and writes through rbuff
without holding the lock.
An MTU change can therefore race with receive processing. An MTU shrink
can expose the new smaller rbuff with the old larger bound, causing an
out-of-bounds write. A receive callback which already loaded the old
rbuff can instead continue writing after that buffer has been freed.
Serialize receive processing with sl_realloc_bufs() by holding sl->lock
while consuming each receive batch.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Sungmin Kang <726ksm@gmail.com>
Link: https://patch.msgid.link/20260718073631.1674-1-726ksm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set adapter->max_vports only after successful allocation of vports, netdevs
and vport_config buffers. This fixes possible crashes on reset or rmmod,
following failed allocation on init
[ 305.981402] idpf 0000:83:00.0: enabling device (0100 -> 0102)
[ 305.994464] idpf 0000:83:00.0: Device HW Reset initiated
[ 320.416872] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 320.416918] #PF: supervisor read access in kernel mode
[ 320.416942] #PF: error_code(0x0000) - not-present page
[ 320.416963] PGD 2099657067 P4D 0
[ 320.416983] Oops: Oops: 0000 [#1] SMP NOPTI
...
[ 320.417093] RIP: 0010:idpf_remove+0x118/0x200 [idpf]
[ 320.417130] Code: 8b bb 98 09 00 00 e8 17 0f 5b e5 48 8b bb e8 08 00 00 e8 0b 0f 5b e5 66 83 bb 28 06 00 00 00 48 8b bb 20 06 00 00 74 49 31 ed <48> 8b 04 ef 48 85 c0 74 2f 48 8b 78 20 e8 66 58 91 e5 48 8b 83 20
[ 320.417183] RSP: 0018:ff7322212903fdb8 EFLAGS: 00010246
[ 320.417205] RAX: 0000000000000000 RBX: ff4463de40300000 RCX: ff7322212903fd4c
[ 320.417228] RDX: 0000000000000001 RSI: ffffffffa7f7d100 RDI: 0000000000000000
[ 320.417250] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[ 320.417272] R10: 0000000000000001 R11: ff4463de3a638f58 R12: ff4463be89ac7000
[ 320.417294] R13: ff4463be89ac7198 R14: ff4463be94fc7198 R15: ffffffffc0f10f20
[ 320.417317] FS: 00007f963c0e6740(0000) GS:ff4463fdd65d8000(0000) knlGS:0000000000000000
[ 320.417342] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 320.417362] CR2: 0000000000000000 CR3: 00000020ba674002 CR4: 0000000000773ef0
[ 320.417385] PKRU: 55555554
[ 320.417398] Call Trace:
[ 320.417412] <TASK>
[ 320.417429] pci_device_remove+0x42/0xb0
[ 320.417459] device_release_driver_internal+0x1a9/0x210
[ 320.417492] driver_detach+0x4b/0x90
[ 320.417516] bus_remove_driver+0x70/0x100
[ 320.417539] pci_unregister_driver+0x2e/0xb0
[ 320.417564] __do_sys_delete_module.constprop.0+0x190/0x2f0
[ 320.417592] ? kmem_cache_free+0x31e/0x550
[ 320.417619] ? lockdep_hardirqs_on_prepare+0xde/0x190
[ 320.417644] ? do_syscall_64+0x38/0x6b0
[ 320.417665] do_syscall_64+0xc8/0x6b0
[ 320.417683] ? clear_bhb_loop+0x30/0x80
[ 320.417706] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 320.417727] RIP: 0033:0x7f963bb30beb
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-13-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
set_bit(rslt->ptype, prof->ptypes) operates on a DECLARE_BITMAP of
ICE_FLOW_PTYPE_MAX (1024) bits. Nothing prevents a malicious VF from
providing ptype >= 1024 through VIRTCHNL, resulting in a write past
the end of the bitmap and a kernel page fault.
Reproduced with a custom kernel module injecting a crafted
VIRTCHNL_OP_ADD_RSS_CFG on E810-C QSFP (8086:1592),
FW 4.91 0x800214af 1.3909.0, ICE COMMS DDP 1.3.53.0,
kernel 7.1.0-rc1.
crash_parser: ice_parser_profile_init @ ffffffffc0d61b60
crash_parser: setting ptype=0xffff (max valid=1023)
crash_parser: calling ice_parser_profile_init -- expect OOB crash!
BUG: kernel NULL pointer dereference, address: 0000000000000000
Oops: Oops: 0002 [#1] SMP NOPTI
CPU: 56 UID: 0 PID: 165011 Comm: insmod Kdump: loaded Tainted: G S U OE 7.1.0-rc1 #1
Hardware name: Intel Corporation S2600BPB/S2600BPB
RIP: 0010:ice_parser_profile_init+0x2d/0x1d0 [ice]
Call Trace:
<TASK>
? __pfx_ice_parser_profile_init+0x10/0x10 [ice]
crash_init+0x127/0xff0 [crash_parser]
do_one_initcall+0x45/0x310
do_init_module+0x64/0x270
init_module_from_file+0xcc/0xf0
idempotent_init_module+0x17b/0x280
__x64_sys_finit_module+0x6e/0xe0
Bail out early with -EINVAL when ptype is out of range.
Fixes: e312b3a1e209 ("ice: add API for parser profile initialization")
Cc: stable@vger.kernel.org
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-12-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pf->txtime_txqs bitmap tracks which Tx queues have ETF (Earliest
TxTime First) offload enabled. This bitmap is indexed by queue number
and is set by ice_offload_txtime(), which only operates on PF VSI
queues.
However, ice_is_txtime_ena() does not check the VSI type before
consulting the bitmap. When ETF offload is enabled on PF Tx queue 0,
bit 0 is set in pf->txtime_txqs. During a subsequent PCI reset
rebuild, the CTRL VSI's Tx queue 0 is reconfigured and
ice_is_txtime_ena() is called for that ring. Since it only checks
pf->txtime_txqs by queue index without distinguishing VSI type, it
finds bit 0 set and returns true, matching the PF VSI's ETF queue,
not the CTRL VSI's. This causes ice_vsi_cfg_txq() to spuriously
allocate a tstamp_ring for the CTRL VSI ring.
Since CTRL VSI rings have no associated netdev, ice_clean_tx_ring()
takes an early return at the !netdev check before reaching
ice_free_tx_tstamp_ring(), leaking the allocation. Each PCI reset
leaks one 64-byte tstamp_ring.
Fix this by restricting ice_is_txtime_ena() to return true only for
PF VSI rings, since txtime_txqs is only meaningful for PF VSI queues.
Fixes: ccde82e90946 ("ice: add E830 Earliest TxTime First Offload support")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-11-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a PF reset occurs when the PTP state is ICE_PTP_UNINIT, then
ice_ptp_rebuild() will update the state to ICE_PTP_ERROR. This will
result in the following PTP release call trace during driver unload:
kernel BUG at lib/list_debug.c:52!
ice_ptp_release+0x332/0x3c0 [ice]
ice_deinit_features.part.0+0x10e/0x120 [ice]
ice_remove+0x100/0x220 [ice]
This was observed when passing PF1 through to a VM. ice_ptp_init()
fails because ctrl_pf is NULL and sets the state to ICE_PTP_UNINIT.
Fix by detecting the ICE_PTP_UNINIT state in ice_ptp_rebuild() and
returning without error, preventing the invalid state transition to
ICE_PTP_ERROR. The only valid path to ICE_PTP_ERROR is from
ICE_PTP_RESETTING after a failed rebuild.
Fixes: 8293e4cb2ff5 ("ice: introduce PTP state machine")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ptp.cached_phc_time is a 64-bit value updated by a periodic work item
on one CPU and read locklessly on another. On 32-bit or non-atomic
architectures this can result in a torn read. Use READ_ONCE() to
enforce a single atomic load.
Fixes: 77a781155a65 ("ice: enable receive hardware timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-9-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ice_init_lag() associates recipes to profiles, assuming that Link
Aggregation-related profiles will always have profile ID lower than 70
(ICE_PROFID_IPV6_GTPU_IPV6_TCP_INNER). This value seems arbitrary and
might not always be valid for some versions of DDP package, i.e. LAG
profiles may have profile ID greater than 70. This would lead to
misconfigured switch and LAG not working properly.
Fix it by checking up to maximum profile ID.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-7-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
skb_checksum_help() can fail. Pass its return value back to the caller.
Commonize this software path in goto.
Instead of just returning error try calculating software checksum first.
There is a check for TSO in checksum_sw_fb.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently ice_eswitch_attach_vf() is called unconditionally in
ice_start_vfs(), which causes VF creation to fail when CONFIG_ICE_SWITCHDEV
is not defined.
Fix this by adding switchdev mode checks at the call sites before
calling ice_eswitch_attach_vf(), consistent with how
ice_eswitch_attach_sf() is already handled in ice_devlink_port_new().
This is similar to commit aacca7a83b97 ("ice: allow creating VFs for
!CONFIG_NET_SWITCHDEV") which fixed the same issue for the previous
ice_eswitch_configure() API.
Fixes: 415db8399d06 ("ice: make representor code generic")
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260717185340.3595286-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The egress rate calculation computes an incorrect mantissa and exponent,
causing up to ~50% deviation from the configured rate at lower speeds.
Rework the computation to follow the hardware rate formula:
rate = 2 * (1 + mantissa/256) * 2^exp / (1 << div_exp)
Keep div_exp = 0 and derive exp and mantissa from half of the requested
rate. Rates below 2 Mbps are floored to the smallest encodable step
(exp = 0, mantissa = 0).
Fixes: e638a83f167e ("octeontx2-pf: TC_MATCHALL egress ratelimiting offload")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Nitin Shetty J <nshettyj@marvell.com>
Link: https://patch.msgid.link/20260717084349.2227796-1-nshettyj@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
uea_probe() distinguishes a pre-firmware device from a post-firmware one
using the USB id (UEA_IS_PREFIRM()), and stores a different object as the
interface data in each case: a 'struct completion' for a pre-firmware
device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a
post-firmware one.
uea_disconnect() instead tells the two apart by the number of interfaces
of the active configuration (a pre-firmware device exposes a single
interface, ADI930 has 2 and eagle has 3), and casts the interface data
accordingly.
Because the two handlers use different criteria, a crafted device that
advertises a pre-firmware id together with a multi-interface descriptor
(or a post-firmware id with a single interface) makes them disagree: the
small 'struct completion' stored by uea_probe() is then passed to
usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes
instance->serialize, reading past the end of the allocation:
BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80
Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982
...
__mutex_lock+0x152a/0x1b80
usbatm_usb_disconnect+0x70/0x820
uea_disconnect+0x133/0x2c0
usb_unbind_interface+0x1dd/0x9e0
...
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes to the right of
allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60)
Reject such inconsistent descriptors in uea_probe() so that both handlers
always make the same pre/post-firmware decision.
Reported-by: syzbot+e62a973f8322b3bbe3ac@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e62a973f8322b3bbe3ac
Fixes: e2674dfbed8a ("usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect()")
Signed-off-by: Diego Fernando Mancera Gomez <diegomancera.dev@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260717080704.1264-1-diegomancera.dev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Credit Based (CB) TSA is not supported by the mlx5 driver, so reject
any configurations that specify it.
Fixes: 08fb1dacdd76 ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260717075125.1244877-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IEEE 802.1Qaz standard defines that bandwidth allocation percentages
only apply to Enhanced Transmission Selection (ETS) traffic classes.
For STRICT and VENDOR transmission selection algorithms, bandwidth
percentage values are not applicable.
Currently for non-ETS 100 bandwidth is being reported for all traffic
classes in the get operation due to hardware limitation, regardless of
their TSA type.
Fix this by reporting 0 for non-ETS traffic classes.
Fixes: 820c2c5e773d ("net/mlx5e: Read ETS settings directly from firmware")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260717075125.1244877-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 2a22b7ae2fa3 ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
added a path in xpcs_get_state_c37_sgmii() that reads speed/duplex from
BMCR after AN completes. However, BMCR does not reflect the negotiated
result on the hardware where this has been tested:
- On RK3568 (MAC side SGMII), BMCR returns a fixed hardware reset value
- Wangxun engineer Jiawen Wu confirmed that on their side, "BMCR looks
like it only wants to be return as 0" [0]
The correct information is available in CL37_ANSGM_STS, which contains
the actual link status and negotiated speed/duplex.
This bug was previously masked by phylink core, which overrides the PCS
link state with the PHY state when a PHY is present:
/* If we have a phy, the "up" state is the union of both the
* PHY and the MAC
*/
if (phy)
link_state.link &= pl->phy_state.link;
Thus, when the link is down, the PHY's link_down state is applied on top
of whatever the PCS reports, hiding the broken PCS state reading path.
Modify xpcs_get_state_c37_sgmii() to:
1. Read link state from CL37_ANSGM_STS
2. If link is up, report speed/duplex from CL37_ANSGM_STS
3. Remove the broken BMCR reading path entirely
Also properly set state->an_complete to reflect the AN completion status,
and clear CL37_ANCMPLT_INTR when link is down to avoid stale state.
[0] https://lore.kernel.org/all/000c01dd1593$2ac0b0f0$804212d0$@trustnetic.com/
Fixes: 2a22b7ae2fa3 ("net: pcs: xpcs: adapt Wangxun NICs for SGMII mode")
Cc: stable@vger.kernel.org
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260717074324.3250043-2-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
esw_egress_acl_vlan_create() hardcodes num_dest=0 in its
mlx5_add_flow_rules() call. When invoked from the non-bond path
fwd_dest is NULL and num_dest=0 is correct. When invoked from
esw_acl_egress_ofld_rules_create() during a bond event, fwd_dest is
non-NULL and flow_act.action carries MLX5_FLOW_CONTEXT_ACTION_FWD_DEST,
but _mlx5_add_flow_rules() rejects a non-NULL dest pointer paired with
dest_num<=0 and returns -EINVAL. The error propagates as
"configure slave vport egress fwd, err(-22)". The passive vport's egress
ACL table ends up with its flow groups allocated but no FTEs, so
prio-tagged packets are not popped and bond failover is broken on
prio_tag_required devices.
Fix by passing fwd_dest ? 1 : 0 as num_dest to match the actual number
of destinations supplied.
Fixes: bf773dc0e6d5 ("net/mlx5: E-Switch, Introduce APIs to enable egress acl forward-to-vport rule")
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260717073306.1242399-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MCIA register can return up to 32 dwords (128 bytes) when the device
advertises the mcia_32dwords capability, but struct
mlx5_ifc_mcia_reg_bits only defines dword_0..11, leaving room for just
12 dwords (48 bytes) of data.
mlx5_query_mcia() clamps the read size to mlx5_mcia_max_bytes() and then
memcpy()s that many bytes out of the register, potentially reading past
the end of the 'out' buffer. On kernels built with FORTIFY_SOURCE this
is caught as a buffer overflow while reading the module EEPROM via
ethtool:
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1048!
RIP: 0010:fortify_panic+0x13/0x20
Call Trace:
mlx5_query_mcia.isra.0+0x200/0x210 [mlx5_core]
mlx5_query_module_eeprom_by_page+0x4a/0xa0 [mlx5_core]
mlx5e_get_module_eeprom_by_page+0xbb/0x120 [mlx5_core]
eeprom_prepare_data+0xf3/0x170
ethnl_default_doit+0xf1/0x3b0
Extend the mcia_reg layout to 32 dwords.
Fixes: 271907ee2f29 ("net/mlx5: Query the maximum MCIA register read size from firmware")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260717072338.1240582-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns geneve->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in geneve->net can rewrite a geneve
device whose underlay lives in geneve->net.
geneve_changelink() applies the new configuration against geneve->net:
geneve_link_config() and the geneve_quiesce()/geneve_unquiesce() pair
reopen the underlay sockets in that netns (geneve_sock_add() uses
geneve->net), so the same reasoning as the tunnel changelink series
applies here.
Gate geneve_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 5b861f6baa3a ("geneve: add rtnl changelink support")
Cc: stable@vger.kernel.org
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260716203500.70573-3-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the sticky underlay netns vxlan->net. They differ once the device is
created in or moved to a netns other than the one the request runs in.
The rtnl changelink path checks CAP_NET_ADMIN only against dev_net(dev),
so a caller privileged there but not in vxlan->net can rewrite a vxlan
device whose underlay lives in vxlan->net.
vxlan_changelink() validates and applies the new configuration against
vxlan->net (vxlan_config_validate(vxlan->net, ...)) and can reopen the
underlay socket in that netns, so the same reasoning as the tunnel
changelink series applies here.
Gate vxlan_changelink() with rtnl_dev_link_net_capable(), at the top of
the op before any attribute is parsed, matching ipgre_changelink() and
the rest of the "require CAP_NET_ADMIN in the device netns for
changelink" series.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 8bcdc4f3a20b ("vxlan: add changelink support")
Cc: stable@vger.kernel.org
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260716203500.70573-2-doruk@0sec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rss_indir_user and rss_hkey_user are allocated and filled in
__set_rss_rxfh() when the user configures RSS via ethtool, but
nothing ever reads them. hinic_get_rxfh() fetches the state from
the device, and the hardware is programmed from the original
indir/key arguments. These buffers only leaked on driver unload.
Drop the unused allocations, memcpys, and struct fields.
Fixes: 4fdc51bb4e92 ("hinic: add support for rss parameters with ethtool")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260722025353.328179-1-chenguang.zhao@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only register the physical clock when facility 28 is installed
and PTFF QAF returns that PTFF QPT is available.
Fixes: 2d7de7a3010d ("s390/time: Add PtP driver")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Cc: stable@kernel.org
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20260714130342.1971700-3-svens@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pppoe_sendmsg() saves a pointer to the PPPoE header before calling
dev_hard_header(). Device header callbacks are allowed to reallocate the
skb head, invalidating pointers into it.
This can happen when a send is blocked in copy_from_user() while the first
non-Ethernet port is added to an empty team device. The team's delegated
GRE header callback then expands the skb head. PPPoE subsequently writes
six bytes through the stale pointer into the freed head.
Reload the PPPoE header through the skb's network-header offset after
device header creation. pskb_expand_head() updates that offset when it
relocates the head.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Asim Viladi Oglu Manizada <manizada@pm.me>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260722093814.3017176-1-manizada@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several fields in struct ppp can be read or updated concurrently
from multiple CPUs without synchronization, causing data races:
1. ppp->mru is read concurrently in ppp_receive_nonmp_frame() while
being updated via PPPIOCSMRU ioctl. Protect ppp->mru updates in
PPPIOCSMRU with ppp_recv_lock(ppp).
2. PPPIOCGFLAGS reads ppp->flags, ppp->xstate, and ppp->rstate
unlocked. Wrap the read in ppp_lock(ppp) to get a consistent
snapshot.
3. ppp->debug is updated via PPPIOCSDEBUG and read concurrently on
fast paths. Annotate reads with READ_ONCE() and writes with
WRITE_ONCE().
4. ppp->last_xmit and ppp->last_recv are updated on TX/RX data paths
and read via PPPIOCGIDLE32 / PPPIOCGIDLE64 ioctls. Annotate with
WRITE_ONCE() / READ_ONCE() and use max() to handle jiffies
subtraction.
5. ppp->npmode[] is updated via PPPIOCSNPMODE and read on TX/RX
paths. Annotate with WRITE_ONCE() / READ_ONCE().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Qingfang Deng <qingfang.deng@linux.dev>
Link: https://patch.msgid.link/20260722101605.2868548-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When an AMT device is removed, pending delayed works can still access
the freed amt_dev structure, which may result in kernel crashes or
memory corruption.
amt_dev_stop() cancels req_wq and discovery_wq with
cancel_delayed_work_sync(), but these works can be scheduled again
from event_wq after the cancellation. This allows delayed works to
access the freed amt_dev structure after the netdev has been released.
The following is a simple race scenario:
CPU0 CPU1
amt_dev_stop()
cancel_delayed_work_sync()
amt_event_work()
mod_delayed_work(req_wq)
free netdev
req_wq accesses freed amt_dev
Use disable_delayed_work_sync() in amt_dev_stop() to prevent req_wq and
discovery_wq from being queued again and wait for running work items
to complete.
The delayed works are disabled after initialization in
amt_newlink() and enabled only when the device is successfully opened.
This keeps the delayed work lifecycle synchronized with the lifetime
of the AMT device.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface")
Cc: stable@vger.kernel.org
Signed-off-by: Shihuang Liu <shlomojune6@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20260722113919.7723-1-shlomojune6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
tested:
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: a0c2ccd9b5ad ("mctp: Add MCTP-over-serial transport binding")
Cc: stable@vger.kernel.org
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715082021.46315-1-doruk@0sec.ai
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When MCAM entries are allocated for a VF netdev via the devlink
mcam_count parameter, only OTX2_FLAG_NTUPLE_SUPPORT was set. That
enabled ethtool ntuple filters but not tc flower offload. Also set
OTX2_FLAG_TC_FLOWER_SUPPORT when entries are successfully allocated.
Fixes: 2da489432747 ("octeontx2-pf: devlink params support to set mcam entry count")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715052007.2099851-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
stmmac_mac_link_down() clears the MAC's transmit and receive enable bits.
stmmac_mac_link_up() is expected to set them again through
stmmac_mac_set(..., true), but it first switches on the negotiated speed
and returns early for a speed the switch does not list. The MAC is then
left gated off.
The speed selection is split into three switches, keyed on the interface.
The generic branch -- taken for everything that is neither USXGMII nor
XLGMII, so including PHY_INTERFACE_MODE_10GBASER -- lists only SPEED_2500,
SPEED_1000, SPEED_100 and SPEED_10.
MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does
rate matching, so phylink_link_up() replaces the media speed with the
MAC-side interface speed before calling into the MAC:
case RATE_MATCH_PAUSE:
speed = phylink_interface_max_speed(link_state.interface);
duplex = DUPLEX_FULL;
The driver is therefore called as
stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)
which falls through to "default: return;". The interface stops passing
traffic after the first link flap.
The failure is easy to misread. The link still comes up, because the PHY
is polled over MDIO and needs no MAC, so the interface reports carrier 1
at the media speed. The DMA is untouched, so its start bits stay set and
descriptors are still consumed. Only the MAC itself is gated off: the
receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0)
and nothing reaches the wire (TE is 0). The interface survives boot only
because stmmac_hw_setup(), called from ndo_open, enables the MAC
unconditionally -- so the problem appears only once the cable has been
unplugged and plugged back in, and "ip link set dev <ethX> down && ip
link set dev <ethX> up" appears to fix it.
The interface is not what the speed bits depend on: with the single
exception of 2.5G, which is selected through the XGMII block on USXGMII
and through the regular speed bits otherwise, each speed maps to one
field of struct mac_link. The per-interface switches are speed
validation, and phylink already validates the speed against
priv->hw->link.caps. So collapse the three switches into one keyed on the
speed alone, keeping the interface test only for the 2.5G case. This
covers 10G on 10GBASE-R, and equally 5G, and 1G/100/10 on USXGMII, all of
which hit "default: return;" today.
A core that does not support a speed leaves the corresponding mac_link
field at 0, and phylink will not offer it that speed in the first place.
For dwxgmac2 at 10G, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000,
which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl
then equals old_ctrl, the register write is skipped, and execution
reaches stmmac_mac_set(..., true).
Log an error in the default case, since a speed with no entry here leaves
the MAC disabled and the symptom does not point at the cause.
Fixes: d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: vadik likholetov <vadikas@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260713074911.30090-1-vadikas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When deleting an L3/L4 flower filter entry, the action field is not
reset. If a filter was previously configured with a drop action, that
action may persist and affect subsequent filter configurations
unintentionally.
Clear the action field when the filter entry is deleted.
Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-5-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The basic flow parser in tc_add_basic_flow() does not validate match
keys before proceeding. Unsupported offload configurations such as
partial protocol masks, non-IPv4 network proto, or non-TCP/UDP transport
proto are silently accepted instead of returning -EOPNOTSUPP.
Add validation to return -EOPNOTSUPP early for:
- No network or transport proto present in the key
- Partial protocol mask (only full mask supported)
- Network proto is not IPv4
- Transport proto is not TCP or UDP
Each rejection includes an extack message so the user knows which part
of the match is unsupported.
Also propagate -EOPNOTSUPP from tc_add_basic_flow() in tc_add_flow()
by returning it directly rather than using break. The break was silently
discarding the error for FLOW_CLS_REPLACE operations where entry->in_use
is already true, causing tc_add_flow() to return 0 (success) for
unsupported replace requests.
Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-4-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The XGMAC_L4_ADDR register holds both source and destination port
match values. The current implementation overwrites the entire register
when configuring either port, so setting one silently erases the other.
Fix this by reading the register first, then masking and updating only
the relevant field before writing back.
Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Signed-off-by: Nazim Amirul <muhammad.nazim.amirul.nazle.asmade@altera.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260714023716.29865-3-muhammad.nazim.amirul.nazle.asmade@altera.com
Reviewed-by: Jakub Raczynski <j.raczynski@samsung.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
drm_gem_shmem_test_purge [1] and drm_gem_shmem_test_get_pages_sgt [2]
intermittently fail on ppc64le and s390x CI systems with a DMA address
overflow:
DMA addr 0x0000000100307000+4096 overflow (mask ffffffff, bus limit 0)
WARNING: kernel/dma/direct.h:114 dma_direct_map_sg+0x778/0x920
drm_gem_shmem_test_purge: ASSERTION FAILED at
drivers/gpu/drm/tests/drm_gem_shmem_test.c:330
Expected sgt is not error, but is: -5
The call chain leading to the failure is:
drm_gem_shmem_test_purge() / drm_gem_shmem_test_get_pages_sgt()
drm_gem_shmem_get_pages_sgt()
drm_gem_shmem_get_pages_sgt_locked() [drm_gem_shmem_helper.c]
dma_map_sgtable() [mapping.c]
__dma_map_sg_attrs()
dma_direct_map_sg() [direct.c]
dma_direct_map_phys() [kernel/dma/direct.h]
dma_capable() Checks addr against DMA mask
-> FAILS: addr > 0xFFFFFFFF
The root cause is that KUnit devices are initialized with a 32-bit DMA
mask (DMA_BIT_MASK(32)) in lib/kunit/device.c. On ppc64le and s390x
systems with physical memory above 4GB, page allocations can land at
addresses that exceed this mask. When drm_gem_shmem_get_pages_sgt()
attempts to DMA-map these pages via dma_map_sgtable(), the DMA layer
rejects the mapping because the physical address overflows the 32-bit
mask.
The failure is intermittent because pages may or may not be allocated
above 4GB on any given run depend on memory pressure.
Fix by setting a 64-bit DMA mask on the device before calling
drm_gem_shmem_get_pages_sgt() for all tests, following the same pattern
already used in drm_gem_shmem_test_obj_create_private().
[1] https://s3.amazonaws.com/arr-cki-prod-trusted-artifacts/trusted-artifacts/2643976103/test_s390x/15128551935/artifacts/jobwatch/logs/recipes/21561049/tasks/220716793/results/1014626315/logs/dmesg.log
[2] https://s3.amazonaws.com/arr-cki-prod-trusted-artifacts/trusted-artifacts/2643976103/test_ppc64le/15128551933/artifacts/jobwatch/logs/recipes/21561041/tasks/220716705/results/1014628163/logs/dmesg.log
Fixes: 93032ae634d4 ("drm/test: add a test suite for GEM objects backed by shmem")
Closes: https://datawarehouse.cki-project.org/issue/5345
Closes: https://datawarehouse.cki-project.org/issue/3184
Assisted-by: Claude:claude-4.6-opus
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: José Expósito <jose.exposito@redhat.com>
Link: https://patch.msgid.link/20260703150808.3832-1-jose.exposito89@gmail.com
|
|
Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made
xe_svm_init() unconditional in xe_vm_create() and extended it to also
initialize a "simple" gpusvm state for non-fault-mode VMs. The matching
xe_svm_fini() call in xe_vm_close_and_put() was updated to run
unconditionally, but the error unwind path in xe_vm_create() was not.
On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has
already succeeded but xe_svm_fini() is only called when
XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves
vm->svm.gpusvm partially initialized and leaks the resources allocated
by drm_gpusvm_init().
For fault-mode VMs, xe_svm_init() additionally acquires the pagemap
owner via drm_pagemap_acquire_owner() and the pagemaps via
xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(),
not xe_svm_fini(). On the same error path, xe_svm_close() is not
called either, so fault-mode VMs leak the pagemap owner and pagemaps.
Fix both leaks:
- Call xe_svm_fini() unconditionally on the err_svm_fini path, matching
the unconditional xe_svm_init() call. Move the vm->size = 0
assignment out of the conditional so the xe_vm_is_closed() assert in
xe_svm_fini() (and xe_svm_close()) holds for both modes.
- Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching
the ordering used in xe_vm_close_and_put().
Fixes: 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm")
Cc: Matthew Auld <matthew.auld@intel.com>
Assisted-by: Claude:claude-opus-4.7
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260721205516.4058959-2-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
PCI bus, device and function can be same for devices existing across
different domains. Allow per domain unique identifier while registering
platform device to prevent name conflict.
Fixes: f0e53aadd702 ("drm/xe: Support for I2C attached MCUs")
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260721113438.651100-1-raag.jadav@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit a79f6abc8b516b5bd906e2eca8121e3549ee163f)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
vmxnet3_get_hdr_len() assumes gdesc->rcd.v4/v6/tcp always describe the
outer header, but for a Geneve-encapsulated packet the device can set
them based on the inner header instead, signalled by the
VMXNET3_RCD_HDR_INNER_SHIFT bit in the completion descriptor. Since the
function never skips the outer encapsulation, this mismatch triggers:
- BUG_ON(hdr.ipv4->protocol != IPPROTO_TCP), because the outer
protocol is UDP (Geneve), not TCP.
- BUG_ON(hdr.eth->h_proto != ...), when the tunnel's outer and inner
IP versions differ (e.g. outer IPv6/inner IPv4 or vice versa).
Check VMXNET3_RCD_HDR_INNER_SHIFT up front and bail out, since the
function cannot locate the inner header it would need to parse. Also
convert the remaining BUG_ON()s in this function to return 0
defensively.
Fixes: 45dac1d6ea04 ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)")
Signed-off-by: Harshaka Narayana <harshaka.narayana@broadcom.com>
Reviewed-by: Ronak Doshi <ronak.doshi@broadcom.com>
Reviewed-by: Sankararaman Jayaraman <sankararaman.jayaraman@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260713140915.3381715-1-harshaka.narayana@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|